Structural Design & Architectural Drawings

Structural engineering develops the supports, foundations and connections that allow the architectural design to be built. Our consulting Chartered Structural Engineer, Stephen D’Aulby, works with our surveying and architectural team on residential and commercial projects, from individual beams and structural alterations to the design of a building.

Existing architectural drawings, earlier calculations and the proposed layout help establish what needs to be designed. An inspection and measurements may provide the remaining information, although concealed supports, connections or foundations can require targeted investigation. Identifying this early helps resolve the design before contractors price or start the work.

Timber roof framing, steel supports and blockwork during construction
Coordinating framing, walls & openings
Local opening in masonry above a protected roof surface
Investigating existing construction

Structural Design for Alterations & Extensions

Structural Design for Extensions

An extension adds weight to the ground and often involves removing part of an existing wall. The structural design considers the new foundations, floor and roof construction, together with any beams or columns needed where the extension joins the building.

Beam positions and depths affect ceiling levels, openings and the space you can use, so these details are developed alongside the architectural design. Foundation requirements depend on the loads and ground conditions; nearby trees, drains or adjoining foundations may also need investigation before the design can be completed.

Structural Design for Loft Conversions

A loft conversion usually needs a floor designed for use as living accommodation, rather than relying on the existing ceiling joists. The engineering also considers alterations to the roof, the stair opening and the walls or other supports that will carry the new loads.

Floor depths, beam positions and roof supports need to work with the proposed room layout and usable headroom. Coordinating these with the architectural drawings helps establish a workable design before construction, particularly where a dormer or new staircase changes the existing arrangement.

Removing Walls & Forming Openings

When a loadbearing wall is removed, the weight it carries has to pass through new supports to the structure and foundations below. The design therefore considers the beam, its bearings or supports at each end, and whether the existing walls and foundations can carry the resulting loads.

A wide opening may require columns or a frame, which can affect the width of the opening and the work needed below floor level. Establishing the support arrangement early allows the structural details to be coordinated with the layout.

Investigating Structural Problems

Cracking, movement or distortion needs to be considered in the context of the building. Stephen assesses the affected structure, previous alterations and the available history to establish what the evidence shows and whether further investigation is needed before repairs can be recommended.

Where it is unclear whether movement is continuing, monitoring may help establish how the building is behaving over time. Opening-up, drainage or ground investigations may be appropriate in other cases. When structural concerns overlap with defects in the building fabric, we coordinate the engineering assessment with our Building Surveying work.

Structural Calculations & Details

Structural calculations set out the loads, assumptions and checks supporting the design. The accompanying drawings and details show the designed arrangement, including member sizes, connections and supports, so the contractor has the information needed to construct the relevant elements.

This information supports the Building Regulations application and is coordinated with the architectural drawings. The building design also needs to address matters such as fire protection, insulation and ventilation; for example, the enclosure around a steel beam may affect both fire resistance and the finished ceiling level.

Temporary Support During Construction

While a wall is being removed or a roof altered, the building may need temporary props or bracing. The support arrangement and sequence of work need to be planned before construction begins, with responsibility for the necessary temporary works design clearly established.

The contractor must arrange competent advice and any design needed to carry out the work safely. Calculations for the finished structure do not, by themselves, explain how to support it during construction, and a permanent structural design appointment does not automatically include temporary works design or coordination.

Frequently Asked Questions

When should I involve a structural engineer?

Involve the engineer while the layout is being developed if the project includes new openings, additional floors, altered roof supports or significant new loads. Early structural advice can inform the architectural design, especially where beam depths, columns or foundations affect what you want to achieve.

Can you use existing structural calculations?

Earlier calculations can help explain the existing structure, but they need to be checked against the building and the work now proposed. A different opening, loading or support arrangement may require revised calculations, even if part of the earlier design appears similar.

Do you work on commercial buildings?

Stephen’s experience includes residential and commercial structural design, using steel, concrete and timber. His work ranges from individual beams and columns to foundations, retaining walls and the structural design of a building. We can coordinate the engineering with our architectural services or discuss an assessment of an existing structure.

What if the builder finds something different on site?

If the exposed wall, support or connection differs from the design assumptions, the affected detail needs to be reviewed before that part of the work proceeds. The same applies if the builder proposes a different beam or support arrangement: any revised engineering must be coordinated with the architectural drawings.

Does the appointment include site inspections?

The proposal should identify the inspections included and whether further visits are needed during construction. Design calculations alone do not provide ongoing site supervision. Where the engineer needs to inspect a particular support or connection, the timing should be arranged before the work is covered over.

Do I need a Building Survey or a structural assessment?

We can help with either. A Building Survey considers the property’s overall condition and repair needs, while an assessment by our consulting Chartered Structural Engineer focuses on a structural concern or proposed alteration. Send us the relevant survey pages, photographs or drawings so we can recommend the appropriate appointment.

Related Services & Guidance